Guide
Load securing in vans
The load must be stowed and secured so that it does not slide, tip or fall even under full braking or a sudden swerve (section 22 StVO). Under section 412 HGB the sender generally loads in a manner safe for carriage; the carrier ensures loading that is safe for operation.
Load securing is no formality: an unsecured pallet in a van becomes a projectile under full braking. Duties are shared – between sender, driver and vehicle keeper. Knowing who does what avoids disputes, damage and fines.
Who does what – sender, driver, recipient
Load securing is teamwork. Under § 412 HGB the sender generally loads, stows and secures the goods safely for transport unless agreed otherwise; the carrier – that is us as the contracted transport company, in practice through our driver – ensures loading is safe for operating the vehicle. Under § 22 StVO the load and its securing devices must be secured so that it does not slide, tip over, roll about or fall off under full braking or a sudden evasive manoeuvre.
In practice: you provide the goods ready for transport – packed, stacked, wrapped. The driver checks, positions the load tightly in the vehicle and lashes it. The recipient accepts and notes visible damage right at handover.
| Role | Task | Typical example |
|---|---|---|
| Sender | provide and load safely for transport | pallet wrapped, cartons closed |
| Driver | load safely for operation, secure | straps, anti-slip mat, tight positioning |
| Recipient | accept, note damage | visual check at handover |
Securing in a van: how it works
In a van tight positioning comes first: place goods flush against the bulkhead or other cargo, fill gaps with padding or empty pallets, then strap down or tie directly at the lashing points. Anti-slip mats under pallets and heavy cartons increase friction considerably and reduce the strap tension needed.
Heavy items go at the bottom and as close to the bulkhead as possible; tall and narrow items are secured against tipping. The permissible axle loads and payload set the limit – even if space remains. Why weight often limits before space is explained in the guide vans: dimensions and payload.
Pallets on curtainside vans and trucks
On the flatbed of a curtainside van and in a 7.5-tonne truck pallets usually stand lengthwise in rows. The curtain alone is not load securing: pallets are strapped down or held with load bars against sliding. With a part load, too, the cargo is positioned according to the vehicle's load distribution – often against the bulkhead, but centre of gravity and permissible axle loads decide.
Non-stackable pallets must be marked. Mixed loads of pallets, mesh boxes and cartons are planned by the driver so that heavy items are at the bottom and front. How many pallets fit on which floor is shown in Euro pallets per vehicle.
What to prepare before collection
- Pallets wrapped or strapped, no overhang beyond the pallet edge.
- Note and state the weight per pallet or piece.
- Mark non-stackable or tip-sensitive goods.
- Bundle long items, protect sharp edges.
- Have a pallet truck or forklift ready at collection if needed.
- If unsure: attach photos of the goods to the request.
Common mistakes – and how we avoid them
Most problems arise not in the vehicle but before it: pallets with overhanging goods, cartons without filling material or an underestimated weight. That is why we ask for dimensions, weight and type of goods before the run. If something does not fit, the driver says so before loading – better a quick fix than risking damage on the way.
Equipment that counts in the vehicle
For securing in the vehicle the driver works with a few effective tools: lashing straps at the lashing points, anti-slip mats, edge protectors for straps, load bars and filling material such as empty pallets or air cushions. What matters is combining them correctly: first position tightly, then add anti-slip material, then lash.
Tight positioning is used wherever possible; where it is not, correspondingly stronger lashing is needed. A single pallet in the middle of an empty load space is harder to secure than the same pallet against the bulkhead with an anti-slip mat underneath.
Example: mixed devices and cartons
An IT department sends four monitors in original cartons, two computers and ten cartons of accessories to a new site. The driver places the heavy computers at the bottom against the bulkhead, the monitor cartons upright next to them, the light cartons on top and in the gaps. Everything is strapped against sliding. The load arrives without movement – and handover is quick because the pieces are numbered, see packing for transport.
Key terms in short
Load securing terms in plain language:
| Term | In short |
|---|---|
| Safe for transport | loaded and stowed so the goods survive the run undamaged – the sender's task under § 412 HGB |
| Safe for operation | loaded so the vehicle drives safely – the carrier's task |
| Tight positioning | load placed flush against the bulkhead or other cargo |
| Friction locking | securing by friction and pre-tension, e.g. lashing down |
| Anti-slip mat | underlay that increases friction between load and floor |
| Lashing point | fixing point in the load space for straps |
What the law requires
Section 22 StVO: secure the load and securing devices so that they do not slide, tip, roll or fall under full braking or a swerve – according to recognised technical rules.
Who loads
Section 412 HGB: unless agreed otherwise, the sender loads, stows and fastens the goods safely for carriage. The carrier ensures loading that is safe for operation.
Blocking before lashing
Place goods tightly against the bulkhead or other cargo, fill gaps, then lash. Anti-slip mats increase friction considerably.
Centre of gravity
Heavy items low, tall and narrow pieces secured against tipping; respect the vehicle's permissible axle loads.
In practice
We choose a vehicle with suitable lashing points and equipment and agree beforehand who loads.
Before departure the driver checks the securing and adds straps, bars or mats if needed – but does not set off if the load is not safe.
Checklist
- Who loads – your staff or our driver?
- Is the cargo palletised or loose?
- Is there a tipping or stacking instruction?
- How heavy is the heaviest single piece?
Good to know
Loading time: under section 412 HGB no separate payment is due for the usual loading and unloading time; if the vehicle waits beyond that for reasons outside the carrier's sphere, demurrage may be charged. Our waiting-time rules are stated in the quote.
Questions and answers: Load securing in vans
Who is responsible for load securing?
Several parties: under section 412 HGB the sender generally loads safely for carriage, the carrier ensures operational safety, and under section 22 StVO the load must be safe in traffic – which the driver also checks.
Is one strap enough for a pallet?
Often not on its own. Better is blocking against the bulkhead or other cargo, plus an anti-slip mat and tie-down lashing or locking bars.
Does your driver load the vehicle?
On request he helps with loading; operational safety is always his job. Who packs and loads safely for carriage is agreed with the request.
Does the driver bring straps and anti-slip mats?
Yes, the vehicle carries securing equipment for normal loads. For special cases such as very long or very heavy single items, talk to us in advance.
May I help with loading?
Yes. If you or your team help with loading, the driver agrees the positioning and takes care of securing for the run.
What about long items such as profiles or pipes?
Bundled, with edge protection and positioned so they cannot slide forward – usually full length against the bulkhead. For items longer than the load space we plan a flatbed or a truck.
What happens if the load cannot be loaded safely?
The driver says so before departure. Together we improve it or plan another vehicle – the run only starts once the load is secure.
Sources
- § 22 StVO – Ladung (gesetze-im-internet.de) (accessed 2026-11-11)
- § 412 HGB (gesetze-im-internet.de) (accessed 2026-11-11)